Truck & Trailer Air Springs: Natural Frequency, Rubber, Failure Signs and Replacement
An air spring is a rubber-and-cord bag that carries your axle load on compressed air. It rarely fails all at once. This guide shows what a failing bag looks like, why its natural frequency sets the ride, how to tell a leak from normal wicking, which rubber suits which environment, and what to match when you order a replacement so it fits the first time.
- An air spring’s natural frequency is set mainly by its air volume and effective area: see equation 4. In an ideal height-controlled spring it does not depend on load (Di Massa et al., 2017).
- Chloroprene is the preferred bellows rubber where weather, mineral oil and heat matter; natural rubber has the lowest glass transition (−70 °C) but swells in oil and needs protection from ozone.
- Federal rules limit air suspension leakage to 3 psi in 5 minutes at normal operating pressure (49 CFR 393.207).
- Hendrickson separates wicking from a leak with a 24-hour test: under 4 psi is wicking, 4 psi or more is a leak.
- Inspect for chafing, rubbing and damage and check ride height; never operate without air in the springs (Hendrickson).
- Buy by the original number, volume and environment rating, not by looks. A near-match can ride differently or fail early.
What does an air spring do?
An air spring replaces a steel spring. Compressed air inside a flexible bellows supports the load, and a height-control valve adds or vents air to hold the vehicle at its set ride height as the load changes. The bellows is layered rubber and cord fabric, and makers qualify it with burst and fatigue tests (Kojic, STED, 2023). In the field, pinholes tend to start at the folded parts of the bellows that flex under pressure (US Patent 9,662,956, background section).
Two shapes cover most applications. In a rolling-lobe (sleeve) spring the bellows rolls over a piston, and the piston’s geometry shapes how the spring behaves (Di Massa et al., 2017). A convoluted spring has one, two or three convolutions (US Patent 10,451,135, background section). They are not interchangeable, even if they bolt up.
What is natural frequency, and why does it matter?
Natural frequency is how many times per second a loaded spring bounces after a bump. The lower it is, the slower and softer the motion, and the less shock reaches the cargo, the frame and the driver. For any spring it is set by just two things, the stiffness and the mass it carries:
where is the natural frequency (Hz), the spring stiffness (N/m) and the supported mass (kg).
Equation 1 explains the familiar harsh ride of an empty trailer on steel springs. A leaf spring’s stiffness k is fixed, so when the load comes off and m drops, the frequency climbs. An air spring avoids this because it does not carry the load with steel. It carries it with air pressure acting on the spring’s effective area:
where is the load on the spring (N), the gauge pressure inside it (Pa) and its effective area (m²).
So when the load doubles, the height-control valve roughly doubles the pressure to hold ride height. That pressure is also what makes the spring stiff. Trapped air resists compression in proportion to how hard it is already pushing (Di Massa et al., 2017):
where is the polytropic exponent of the air (about 1.38 for air springs), the absolute pressure, gauge plus atmospheric, and the air volume (m³).
Load raises the pressure, and pressure raises the stiffness, so the spring stiffens exactly as the mass grows. Writing the mass as F/g and putting equations 2 and 3 into equation 1, the load cancels out:
where is gravitational acceleration (9.81 m/s²) and is the spring’s equivalent height (m).
No load term is left. Once gauge pressure is well above atmospheric, the ratio p/pg is close to 1, and the frequency depends only on the air volume and effective area. That is why a well-matched air suspension rides about the same loaded or empty, the load-independent behaviour Di Massa et al. describe for a height-controlled spring. For an equivalent height of 15 cm the result is about 1.5 Hz, or 91 cycles per minute.
The same equation shows where the small differences come from. On a lightly loaded truck at 20 psi, p/pg is about 1.74, so the spring runs about 32% faster than its high-pressure value; at 100 psi the difference is only 7% (right chart). An empty truck rides a little firmer, but nowhere near as much as on steel. Volume matters more. Because heq = V/Ae sits under the square root, two springs on the same axle compare as:
where are the frequencies and the air volumes of the two springs, or of one spring before and after adding an auxiliary reservoir.
A spring with twice the air volume rides at √½, about 0.71 times the frequency. Effective area works the other way: a smaller area means a softer spring. Makers tune it with the piston profile, and in one test a neutral tapered piston cut the spring rate by 38% (WO 2012/171038). The effective area of a convoluted spring grows as it compresses, while a rolling-lobe spring’s follows its piston shape (Di Massa et al., 2017), so the frequency is not perfectly constant through the stroke.
How often should air springs be inspected?
There is no fixed service life for an air spring; it depends on duty cycle, ride height, clearance and environment. Hendrickson’s trailer maintenance guide lists the air springs as a visual check and ride height as a measured check, with the springs inspected while aired up at ride height (Hendrickson L578, Rev. M, 2024). Its inspection intervals assume about 100,000 miles a year, and higher usage, off-road work or rough conditions call for more frequent checks.
What are the signs of a failing air spring?
| What you see | Likely cause | What to check |
|---|---|---|
| One corner or side sits low, or the unit leans | A leaking or failing bag on that side, or a height-control valve or air line problem | Measure ride height on both sides; check fittings, bead plate and piston for leaks |
| Compressor runs more than usual | Air is escaping somewhere in the suspension circuit | Air lines, fittings and bags; then dryer and compressor output |
| Scuffed or chafed bellows | Rubbing against a line, bracket or frame part (Hendrickson L975) | Line routing and clearance around the full travel of the spring |
| Dirt or debris packed around the piston | Grit abrades the bellows as it rolls (Hendrickson) | Clean the piston; keep it free of dirt and debris |
| Cracks, or cord showing | Rubber ageing and fatigue (PMC review) | Replace the spring |
| Pressure falls faster than the limit | Leak (49 CFR 393.207(f); Hendrickson) | Run the pressure-loss tests below |
| Will not hold ride height after fittings and lines are proven good | Failing spring or height-control valve | Replace a leaking spring; check the valve and its linkage |
What shortens air spring life?
- Rubbing and chafing. Hendrickson’s inspection list calls out chafing, rubbing and damage, and says to keep the area around each spring clear of anything that can touch the bellows (L975; TechTips, 2006).
- Dirt on the piston. Keep air spring pistons free of dirt and debris (Hendrickson TechTips, 2006).
- Running without air or at the wrong pressure. Improper pressure can damage the vehicle or suspension, and the vehicle must not be operated without air pressure in the springs (Hendrickson L975).
- Wrong ride height. Set the suspension to the proper ride height (Hendrickson TechTips, 2006).
- Heat, UV and humidity. They age rubber and degrade its strength and elongation (PMC review), so springs near exhaust or brakes wear faster.
- Oil and heat exposure. See the rubber section below for how each polymer handles oil, heat and ozone (US Patent 10,344,818).
Is it leaking, or just wicking?
Two different tests apply, and they answer different questions.
Is the leak within the legal limit? The federal suspension rule requires the vehicle to be level and limits air leakage to no more than 3 psi in a 5-minute period when the gauge shows normal operating pressure (49 CFR 393.207(f)).
Is a damp bag wicking or leaking? Hendrickson calls wicking “a common occurrence and generally considered normal”, and recommends replacing a leaking spring. Its pressure-decay test is: inflate the springs to 20 psi or less, isolate the air lines, and monitor the pressure drop over 24 hours. A drop of less than 4 psi suggests wicking; 4 psi or more indicates a leak (Hendrickson TechTips, June 2025). Hendrickson’s test applies to its own air springs, so for other makes refer to the air spring manufacturer’s information.
How do you inspect an air spring?
- Ride height. Check it with the springs aired up, and compare it with the suspension maker’s specification (Hendrickson L578).
- Chafing, rubbing, damage. Look over each bellows for scuffs, cuts and cracks (Hendrickson L975).
- Clearance. Make sure no line, bracket or frame part touches the bellows through its full travel (Hendrickson TechTips, 2006).
- Piston. Clean off dirt and debris.
- Leaks. Spray the fittings, bead plate and piston area with soapy water and look for bubbles.
- Shocks and down-stops. Check for leaks or damage (Hendrickson L975).
- Air supply. Note a compressor that cycles too often.
Safety: depressurize the system before working on it. If a trailer is supported by its landing gear, lower it onto the internal air spring bumpers (Hendrickson L975).
When should you replace an air spring?
Replace a spring that fails the leak tests, shows cracks or cord, or will not hold ride height once the fittings and lines are proven good. Hendrickson’s own guidance is to replace a leaking air spring (TechTips, June 2025).
Our recommendation is to change both springs on the axle together, and to look at the shocks while the springs are off. Matched springs age at the same rate, so the axle rides evenly and you are not back in the shop for the second one.
Which rubber suits which environment?
A bellows is a composite: an inner rubber layer, rubberized cord plies and an outer rubber layer. In one Continental rolling-lobe design the cord is three layers of nylon fabric, rubberized with a polychloroprene mixture, with cord angles of 40° to 80°, and the spring must withstand operating pressures of 10 bar (about 145 psi) and higher (US 5,566,929). The rubber seals the air, bonds the plies and shields the cord. Failure modes include bursting between widely spaced cords, and bending fatigue where the lobe rolls (US 7,063,308).
| Base polymer | Low temperature (glass transition) | Oil | Ozone and weather | Role in air springs |
|---|---|---|---|---|
| Natural rubber (NR) | −70 °C | Poor; swells in oils (Kiattanavith, 1988) | Poor unless protected; antiozonants work less well in NR (US Army, 1976) | Inner and outer layers in a ContiTech bellows example (US 10,344,818) |
| Chloroprene (CR) | −50 °C | Good | “Very good resistance to weathering, mineral oil and heat” (US 10,344,818) | Preferred bellows rubber in that patent; rubberizes cord plies; basis of ContiTech’s hi-temp spring |
| EPDM | −55 °C | Poor | Excellent; it protected diene rubbers it was blended with in long-term outdoor tests (US Army, 1976) | Listed as a candidate polymer in the same patent |
| SBR | −60 °C | Poor | Poor resistance to light, oxygen and ozone (course materials) | Listed as a candidate; not the preferred bellows rubber |
Glass transition and oil ratings: Rubber Technology Lecture 4, Elastomer Materials (University of Technology). Glass transition is where rubber turns glassy, so real low-temperature flexibility is limited well above it. The table shows base-polymer tendencies, not the rating of any one spring, because makers blend polymers by layer.
Heat. NR and SBR have relatively poor heat resistance (course materials). In ContiTech’s 2015 test, a chloroprene-based hi-temp air spring gave twice the service life of its standard spring at 80 °C in a climate chamber, and the company noted that “the proximity to the vehicle exhaust system places higher thermal stress on the air springs.”
| Where it works | What attacks the bellows | What to look for |
|---|---|---|
| Cold winters | Rubber stiffens as it approaches its glass transition; NR has the lowest of the group | A published low-temperature rating. ContiTech offers a cold-resistant spring for operation down to −55 °C |
| Hot spots near exhaust, brakes or engine | Heat and oxidation (PMC review) | Chloroprene-based, high-temperature construction |
| Oily or greasy positions, or oil mist from the air system | Oil swells hydrocarbon rubbers; NR and EPDM are poor, CR is good | A CR-based cover, and fix the oil source |
| Strong sun and ozone | Ozone and UV crack unsaturated rubber under tension | A protected or saturated-polymer cover compound |
| Normal highway duty | Flex fatigue where the lobe rolls | The original-equipment construction and rating |
How do you choose the right replacement?
- Original number. Read it from the old spring’s bead plate or label, or give us the make, model, year and suspension.
- Shape. Rolling-lobe sleeve or convoluted (single, double, triple).
- Design height and travel. The height at normal ride, and the compressed and extended heights.
- Mounting. Top plate stud pattern, air-fitting size and position, and the bottom plate or piston.
- Bumper. Whether the internal bump stop is included and its height.
- Rating. Maximum working pressure, load at design height, and the air volume or natural frequency if the maker publishes it.
- Environment. Rated temperature range and the rubber suited to heat, oil, cold or sun at your mounting position.
- Related parts. Shocks, and the height-control valve if ride height will not set correctly.
This is why we confirm fit against your vehicle or part number before we ship.
What should you send us for a quote?
The number off your old spring, or a photo of the bead plate; your truck or trailer make, model and year; and the suspension if you know it (for example Hendrickson, Kenworth AirLiner or Peterbilt Air Leaf). We confirm fit and send options with pricing and shipping, from Commerce City, Colorado.
Tell us the truck or trailer and the number on the old spring. We confirm fit before we ship.
Running a fleet and want a suspension inspection routine? See our engineering services →
Frequently asked questions
How do I know if my truck’s air bag is bad?
Look for one side sitting low or the unit leaning, a compressor that runs more than usual, chafing or cracks on the bellows, or a pressure drop beyond the limits above.
How much air loss is allowed?
Federal rules limit air suspension leakage to 3 psi in 5 minutes at normal operating pressure (49 CFR 393.207(f)).
Is it normal for an air spring to look damp?
Wicking is common and generally normal. Hendrickson’s test calls a 24-hour drop of under 4 psi wicking and 4 psi or more a leak (TechTips, June 2025).
Do I have to replace both air springs on an axle?
We recommend it. Matched springs age at the same rate and the axle rides evenly.
Can I drive with a flat air spring?
No. Do not operate a vehicle without air pressure in the air springs (Hendrickson L975).
- 49 CFR §393.207 — Suspension systems (Legal Information Institute, Cornell Law School)
- Hendrickson TechTips — Back to Basics: Truck Air Suspension 101 (June 2025)
- Hendrickson L578, Rev. M — Trailer suspension preventive maintenance guide (May 2024)
- Hendrickson L975, Rev. E — INTRAAX suspension inspections and safety (March 2025)
- Hendrickson TechTips — Keeping the spring in air springs (2006)
- Kojic, D. — Investigation of static and dynamic strength of air suspension bellows in heavy vehicles, Zbornik STED 12(1), 2023
- Di Massa, G., Pagano, S., Strano, S. — Stability analysis of air springs subjected to lateral loads, Proceedings of the World Congress on Engineering 2017 (University of Naples Federico II)
- WO 2012/171038 — Air spring with constrained elastic sleeve (natural frequency, effective area, piston shape)
- Bergstrom, E. W. — The long-term effectiveness of chemical vs. polymeric antiozonants in rubber, Technical Report R-TR-76-027, US Army, Rock Island Arsenal, 1976 (DTIC)
- Kiattanavith, N. — Study of the oil-resistance of natural rubber, Journal of the National Research Council 20(2), 1988
- Rubber Technology, Lecture 4: Elastomer Materials (University of Technology)
- Uses of rubber and rubber mixtures 2: special purpose elastomers (course materials, Ankara University)
- ContiTech — Truck air springs for extreme temperatures (press release, September 2015)
- PMC11767060 — Rubber ageing under UV, heat and humidity (National Library of Medicine)
- US Patent 9,662,956 — background on air spring bellows pinholes (USPTO)
- US Patent 10,451,135 — background on air spring types (USPTO)
- US Patent 10,344,818 B2 — Air spring bellows rubber mixtures (ContiTech)
- US Patent 5,566,929 — Rolling-lobe air spring flexible member (Continental)
- US Patent 7,063,308 B2 — Air spring resilient member (ContiTech)
Educational content, not engineering advice. Always follow the suspension and vehicle manufacturer’s specifications for ride height, pressure and installation, and depressurize the system before working on it.