Heavy-duty truck & trailer parts · Ships from Colorado

Heavy-Duty Brake Pad Friction Materials and Edge Codes

Brakes · Engineering guide
By TAG Fleet Parts Engineering · Updated · 2 min read

What the friction on a heavy-duty air disc pad is made of, why it is semi-metallic, and how to read the two letters on its edge — with the physics of why the friction band matters.

Key takeaways
  • Air disc pads are semi-metallic, with more than 50% ferrous content (Fleet Equipment).
  • Phenolic resin is the most common binder; it is brittle and limited in heat resistance (Motta et al., 2023).
  • Graphite is a thermally conductive copper replacement, and its form affects performance (SAE 2015-01-2677).
  • Edge code: first letter = cold friction, second = hot; F means μ 0.35–0.45.
  • Brake torque scales directly with μ, so a lower band means less stopping torque at the same air pressure.

Why are air disc pads semi-metallic?

Air disc brake pads are semi-metallic, with more than 50% ferrous content, while most drum linings are non-asbestos organic (NAO) with little or no ferrous content (Fleet Equipment). Metallic fibers such as steel wool combine mechanical strength and friction with high thermal conductivity (Motta et al., 2023) — the property a pad needs when it absorbs two to three times the energy per square inch of a drum lining.

What holds the friction material together?

A binder — most often a phenolic resin, valued for its performance-to-price ratio and how well it wets the other ingredients. Its weaknesses are brittleness, low impact resistance and limited thermal resistance; carbonization begins around 450°C, lowering density, raising porosity and reducing structural integrity (Motta et al., Materials, 2023).

What replaced copper in the friction?

Copper was valued for conducting heat. Graphite also conducts heat well and is often considered as a copper replacement. In an SAE study of a low-metallic pad with more than 20 wt.% copper removed, two graphite types at 15 wt.% each kept friction stable through the fade section but performed differently — the form of graphite matters, not just its presence (Daei, Majumdar & Filip, SAE 2015-01-2677).

How do you read a brake pad edge code?

The two letters follow the SAE J866 system: the first is the friction coefficient (μ) measured cold, the second hot. The letter bands are written into New York State regulation (15 NYCRR §53.4):

LetterCoefficient of friction (μ)
Cover 0.05, not over 0.15
Dover 0.15, not over 0.25
Eover 0.25, not over 0.35
Fover 0.35, not over 0.45
Gover 0.45, not over 0.55
Hover 0.55

An “FF” pad holds μ 0.35–0.45 both cold and hot. The code classifies the material; it does not by itself prove stopping performance on a given vehicle.

Why the friction band matters

Brake torque on a disc:  T = 2 · μ · F · r
  F = clamp force from the actuator,  r = effective rotor radius
Same air pressure, same caliper:  T ∝ μ
  μ 0.30 instead of 0.40  →  25% less brake torque

That is why a replacement pad should match the friction band the brake was designed around.

Always follow the caliper and vehicle manufacturer’s approved friction specification.

Frequently asked questions

What does FF mean on a brake pad?

FF is an SAE J866 edge code. The first letter is the cold friction band and the second the hot band; F means a coefficient of friction over 0.35 and not over 0.45 (15 NYCRR §53.4). It classifies the material but does not by itself prove stopping performance.

What are the brake pad edge code letters?

C: 0.05–0.15, D: 0.15–0.25, E: 0.25–0.35, F: 0.35–0.45, G: 0.45–0.55, H: over 0.55 coefficient of friction (15 NYCRR §53.4).

Are air disc brake pads semi-metallic?

Yes. Fleet Equipment reports that air disc brake pads are semi-metallic with more than 50% ferrous content, while most drum linings are non-asbestos organic.

What replaced copper in brake pads?

Graphite is a common candidate because it conducts heat well. SAE research (2015-01-2677) found that the type of graphite affects pad performance.

Download the full guide (PDF, 11 pages)
Heavy-Duty Air Disc Brake Pads: Materials, Regulation & Field Performance.
Download PDF

Educational content, not engineering advice. Always follow the caliper and vehicle manufacturer's approved friction specification for your vehicle.